How to Choose Rock Drill Bits, Rods and Threads

Most drilling problems that get blamed on the machine are actually problems with what is screwed onto the end of it. A bit geometry that suits the wrong rock, a rod that is longer than the hole needs, a thread combination that was never meant to meet: each one shows up as slow penetration, crooked holes or a joint that fails early. This guide covers how to choose bit geometry, how the thread decides what fits what, and the published lengths and diameters in the TIGER tooling range.

Key takeaways

  • Bit geometry follows rock condition. Button for general and abrasive rock, ballistic for speed in medium-hard rock, X-bit for straight holes in low-abrasive rock, chisel for fractured ground, retract where holes collapse.
  • The thread is the compatibility decision. TIGER tooling covers R25, R32, R38, T38, T45 and T51, plus R25/Hex22 and the H22 shank family.
  • Hand-held and air-leg drills in the Y and YT range use a 22 × 108 mm shank and drill 32–45 mm holes.
  • Integral rods run 800–8000 mm at 25–42 mm diameter. Extension rods run 800–4300 mm; MF rods are 3660 mm in T45 and T51.
  • Combination couplings such as R25/R32 and R32/R38 exist precisely so a string can step between rod sizes without replacing everything.

1. Start with the hole, not the catalogue

Three facts about the hole determine every item in the string, and in this order: the diameter you need, the depth you need, and the condition of the rock you are drilling through. Everything else follows. A buyer who tells us “a 34 mm bit and 3.5 m rods” has already done this arithmetic; a buyer who asks for “drill bits” has not, and the first thing we send back is these three questions.

Diameter is usually set by the explosive or the wire you intend to put in the hole, or by the splitting method. Depth is set by the bench height or the block you are freeing. Rock condition is the one most often skipped, and it is the one that decides bit geometry.

2. Bit geometry: five types and the rock each suits

All five of these are top-hammer bits, which means the percussion happens at the machine and travels down the string. The carbide at the face is what differs.

BitCarbide formBest inWhat you gainWhat you give up
Button bitSpherical or semi-spherical buttonsWide range of rock, including abrasiveWear resistance and consistent energy transfer; the default choiceNot the fastest in soft or medium rock
Ballistic bitParabolic or conical buttonsMedium-hard rockHigher penetration rate and better debris removalShorter wear life than button in abrasive ground
X-bitTwo intersecting carbide edgesMedium-hard, low-abrasive formationsStraight hole alignment and finer fragmentationWears quickly where the rock is abrasive
Chisel bitSingle wide flat edgeMedium-hard and fractured rockFast penetration with precise controlLess suited to hard, homogeneous rock
Retract bitButton face with retract bodyFractured or loose ground with collapse riskStable hole walls, better flushing, retrievable stringA specialist tool; unnecessary cost in sound rock

If you are unsure, the button bit is the right first order. It is the most widely used geometry in mining, tunnelling and construction for a reason: it tolerates variation in the rock better than the alternatives, and a quarry face is rarely uniform. Move to ballistic when you have confirmed the rock is medium-hard and you want metres per hour. Move to X-bit when hole straightness matters more than wear life, such as when the hole is going to carry a wire. Reach for retract only when you have actually lost a string to a collapsing hole.

Our top-hammer bits cover 32–115 mm across the R25 to T51 thread range. The hand-held and air-leg drills in the Y and YT range drill 32–45 mm, so bits above that diameter belong on rigs and DTH systems rather than on a hand-held machine.

3. The thread decides what fits what

A thread designation is not a quality grade, it is a size and profile. R threads are rope threads, T threads are trapezoidal, and the number is the nominal diameter in millimetres. Energy crosses every joint in the string, so a mismatched or worn thread loses impact energy exactly where you cannot see it.

ComponentAvailable threadsPublished sizes
Integral drill rodsH22 × 108 shank, bit forged on800–8000 mm, Ø 25–42 mm
Extension rodsT45, T51, R32, R25/Hex22800–4300 mm
MF rodsT45, T513660 mm
Shank adaptorsR25/H22, R32/H22Matched to the drill
CouplingsR25, R32, R38, T38, T45, T51Plus R25/R32 and R32/R38 combinations

The combination couplings are worth noticing. R25/R32 and R32/R38 let a string step between rod sizes, which is how an operation upgrades gradually instead of replacing a whole inventory of rods at once. If you are moving from one size to another, ask about these before you order new rods.

4. Integral rod, or extension rod with a coupling?

This is a question about hole depth, and it is the one that saves the most money when answered correctly.

An integral drill rod has the carbide forged onto the rod itself, with an H22 × 108 shank at the other end. One piece, no joints, nothing to lose down the hole. For short holes it is the cheaper and more efficient answer, because every joint you remove is a joint that cannot lose energy or come apart. Our integral rods run from 800 mm up to 8000 mm in 25 to 42 mm diameters, and they are re-sharpenable with a TIGER Grinder rather than discarded when the edge dulls.

An extension string — shank adaptor, rods, couplings, a separate bit — makes sense when the hole is deeper than a single rod can reach, when you want to replace a worn bit without replacing the steel behind it, or when you need to vary depth across a site. It costs more per joint in lost energy, and it gives you something to assemble correctly.

The order of an extension string, from the machine down: rock drill → shank adaptor (R25/H22 or R32/H22) → extension rod → coupling → next rod → bit. The shank adaptor is the part that takes the beating from the machine and the part most often ordered wrong, because it has to match both the drill’s shank and the rod’s thread.

5. What a wrong match actually costs

None of the following shows up as a broken machine, which is why these losses tend to run for months before anyone investigates.

A bit geometry that does not suit the rock drills more slowly and wears faster at the same time, so the cost per metre rises from both directions at once. A worn or mismatched thread absorbs impact energy as heat and movement in the joint, and the operator experiences this as a machine that has lost power. An over-long rod in a shallow hole adds joints and weight for no benefit. A string left unlubricated loses energy at every connection; this is the same mechanism that makes the FY200B line oiler standard equipment on our drills.

The useful metric for all of this is cost per metre drilled rather than the price of the bit, because a cheaper bit that drills fewer metres before discard is not cheaper. We set out how to calculate it in reducing cost per metre drilled, and how to extend the life of what you already own in extending the life of rock-drilling tools.

The rule in one line. Diameter and depth choose the rod; rock condition chooses the bit geometry; the thread on your existing drill chooses everything else.

6. What to tell us when you reorder

Four details let us quote without a round of questions: the drill you are running, the thread you are currently using, the hole diameter and depth, and the rock. If you do not know the thread, the shank size of the drill and a photograph of the rod end are enough for us to identify it. If your bits are wearing faster than they used to and nothing on the site has changed, tell us that too — it usually points to the rock rather than the tooling, and the fix may be a different geometry rather than a bigger order.

What is the difference between a button bit and a ballistic bit?

A button bit carries spherical or semi-spherical tungsten carbide buttons and is the general-purpose choice, with strong wear resistance across a wide range of rock including abrasive ground. A ballistic bit uses parabolic or conical buttons, which penetrate faster and clear debris better in medium-hard rock, but wear more quickly where the rock is abrasive.

Which thread types does TIGER drilling tooling use?

Couplings are available in R25, R32, R38, T38, T45 and T51, with R25/R32 and R32/R38 combination couplings for stepping between rod sizes. Extension rods come in T45, T51, R32 and R25/Hex22, and shank adaptors in R25/H22 and R32/H22.

When should I use an integral drill rod instead of an extension rod?

Use an integral rod for shorter holes that one rod can reach. The carbide is forged onto the rod, so there are no joints to lose energy or come apart, and the rod can be re-sharpened rather than discarded. Use an extension string when the hole is deeper than one rod, or when you want to change a worn bit without replacing the steel behind it.

What is a retract bit for?

A retract bit is for fractured or loose ground where the hole is at risk of collapsing around the string. Its retract body keeps the hole walls stable, improves flushing and allows the string to be withdrawn. In sound rock it is an unnecessary cost, so it is a specialist choice rather than a default.

What lengths and diameters are available?

Integral drill rods run from 800 mm to 8000 mm in diameters of 25 to 42 mm, with an H22 x 108 mm shank. Extension rods run from 800 mm to 4300 mm, and MF rods are produced at 3660 mm in T45 and T51. Top-hammer bits cover 32 to 115 mm across the R25 to T51 range.

What hole diameter can a hand-held rock drill produce?

The Y20, Y24, YT24 and YT28 all drill holes of 32 to 45 mm using drill steels with a 22 x 108 mm shank. Larger diameters require a rig-mounted system or a down-the-hole hammer rather than a hand-held or air-leg machine.

Send us your drill and your rock

Tell us the machine you run, the thread you use, and the diameter and depth you need. Our engineering team will put together the string that fits, and flag it if a different bit geometry would drill your rock better than the one you have been buying.

Request a technical assessment

Benzer Gönderiler