Construction and Infrastructure

Home / Construction and Infrastructure

Every rockfall system, every tieback, every rock-socketed footing hangs on a drilled hole. On a construction site the hole is rarely the point of the work — and that is exactly why the machine gets chosen on access rather than on penetration rate.

This page covers anchor drilling for construction and infrastructure: anchor and tieback holes, foundation holes in rock, slope and rockfall work, and holes at a tunnel face or in a shaft. It sets out what our machines reach, what the specification usually asks for, and the long list of things we do not supply. SET MAKINA has built this equipment in Ankara since 1991.

The short version, if you are only here for a minute

  • We drill the hole. We do not supply what goes in it — no anchors, bars, mesh, netting, barriers or grout, and we are not a contractor.
  • Reach: 32–45 mm to about 10 m on a top hammer, 76–102 mm to 25–30 m with a down-the-hole hammer. Vertical, horizontal and angled.
  • All percussion, all air flush. If your specification calls for air flush and excludes water, that is satisfied by construction rather than by option.
  • The machines are chosen by how you get to the hole: a unit that can be set up on a face, a wheeled unit for repeat positions, a rig on an excavator you already own, or a hand-held drill where nothing else fits.
  • Pneumatic by design — lighter to move on a face, nothing to drown, no electronics, and it stalls instead of burning out.

What drill do you use for rock anchors?

A percussion drill with air flush, on a feed that can be set up where the hole has to go. For most anchor and tieback work that is a top hammer at 32 to 45 mm to around 10 m; for deeper or larger-diameter holes it is a down-the-hole hammer at 76 to 102 mm, which holds its line as the hole lengthens.

What actually decides the choice on site, in the order it bites:

  • Can the machine physically get there. On a slope, in a shaft, under a bridge soffit, inside a tunnel section — this rules out more equipment than any technical parameter.
  • The hole’s diameter and length, which come from the designer rather than from you. Both have to be inside what the machine reaches, with the rods to match.
  • The angle. Anchors are rarely vertical. A feed that only works downward is no use for a tieback into a retaining structure or for a hole at a tunnel crown.
  • What the specification demands of the flush, and whether water is permitted at all.
  • What you already have on the job. A compressor, a hydraulic power pack or an excavator each point to a different answer.
Anchor drilling unit set up on a steep rock face

Four kinds of hole, and what each one asks for

Construction drilling is organised by the purpose of the hole, not by production rate. These are the four we are built for.

Anchor and tieback holes

Holes for rock anchors, soil nails and tiebacks into retaining structures. Usually angled, usually in a line, often from a working platform with no room behind it. The hole has to be straight and clean enough for the anchor to seat and the grout to travel.

Foundation holes in rock

Dowelling a footing into rock, socketing a column, pinning a structure back to competent ground, underpinning an existing foundation. Short holes, tight tolerances, and frequently in a basement or a trench where a large rig cannot stand.

Slope and rockfall holes

The holes that hold a protection system onto a face — draped mesh, pinned netting, a catch fence, an attenuator, or dentition masonry filling a cavity. The constraint here is not the rock, it is standing a machine on a slope without building a platform first.

Tunnel, portal and shaft holes

Face reinforcement, spiling ahead of the face, pinning a portal, stabilising a shaft wall. Confined section, other trades working around you, and sometimes a zone classification — which is the case for an entirely air-driven machine.

Note what is not on that list. Production blastholes and bench drilling belong to quarrying and open-pit work, which is covered on the mining page, not here. The machines overlap; the way you size a fleet for them does not.

How does rockfall protection actually get installed?

The face is cleaned of loose rock first, then the holes are drilled, then the system is hung on them. Scaling before drilling is not optional — anchoring a mesh over material that is about to come away traps the problem behind the system instead of solving it.

  1. Scale the face. Loose and overhanging rock is taken off — by hand with a scaling bar, by high scalers working on rope where the face is tall, or mechanically with an excavator-mounted tool. Trim blasting where the shape itself has to change. The debris is then yarded or cleared from the bench below.
  2. Put in temporary protection if the road stays open. Barriers and catch fences go in before the permanent work where traffic is running beneath.
  3. Drill the anchor pattern. To the designer’s diameter, length, angle and spacing. This is the part we supply the machine for — and on a slope, the question is always whether the machine can be set up at the hole rather than whether it can drill the rock.
  4. Install and tension the anchors, then grout them where the design calls for it.
  5. Hang the system. Draped or pinned mesh, a cable net, a catch fence or an attenuator, fixed to the anchors just installed.
TIGER SMARTROOF pneumatic anchor drilling machine

Where we fit, precisely. Step 3, and nothing else. We do not scale faces, we do not supply scaling bars or rope access, we do not make mesh, netting, fences, attenuators, anchors, bars or grout, and we do not install them. If you are buying a protection system, your supplier is the system manufacturer and your installer is a specialist contractor — we are who they buy the drilling from.

Which machine for which access

Find how you reach the hole in the left-hand column. The figures are from our own specification sheets.

Getting to the holeThe machinePublished figuresWhy this one
On a face or slope, reachable on footSMARTROOF1,700 mm feed stroke · DTH 76–102 mm to 25–30 m · top hammer 32–45 mm to 10 m · 360 kgAn anchor and foundation drill built for ground where you do not build a platform
Several positions along the same faceSMARTROOF-MOBILESame drilling figures, wheeled baseMoving between anchors becomes a manoeuvre rather than a strip-down
Tunnel section, shaft, confined headroomMOBILDRILL1,100–1,600 mm stroke · 360 kg in DTH form, 240 kg on top hammerMobile and small enough to set up and fold away inside a tunnel gauge
You already have an excavator on siteHPDC 160023.9 hp diesel · 210 bar · working height 250–3,700 mm · 2,950 kgTurns the excavator into a drill working vertically, horizontally and at an angle, including overhead
A hydraulic power pack is availableHYDRODRILL100–150 bar · 40–60 L/min · rotation 450–680 N·m at 105–160 rpmHydraulic rotation where compressed air is not on the job
Nothing else will fitHand-held and air-leg drills32–45 mm · 18–26 kgWhat one person can carry to the hole and hold while drilling it
Breaking out, trimming, clearingPneumatic breaker and plug hammerSee each product pageSecondary work where a machine-mounted breaker cannot be positioned

Tell us the diameter, length and angle the designer has specified, plus how the machine gets to the hole, and we will say which of these fits — or that none of them does.

The machines

TIGER MOBILDRILL wheeled pneumatic drilling machine for tunnel and site work

MOBILDRILL
Wheeled, pneumatic, 1,100–1,600 mm feed stroke, 1½” Camlock inlet. Light enough to position in a tunnel section and fold away between shifts.

HPDC 1600 hydro-pneumatic drilling rig mounted on an excavator

HPDC 1600
A hydro-pneumatic rig for permanent mounting on a hydraulic excavator, with its own 23.9 hp diesel unit. 250 to 3,700 mm working height, 2,950 kg. Drills roof, floor and sidewall.

TIGER Y20, Y24, YT24 and YT28 pneumatic rock drills

Hand-held & air-leg drills
Y20, Y24, YT24, YT28 — 32 to 45 mm, 18 to 26 kg. Hand-held for downward and horizontal holes, air-leg where the hole goes up.

TIGER pneumatic down-the-hole hammer for deeper anchor holes

Down-the-hole hammers
From 75 mm. The energy arrives at the bit rather than travelling through the rods, so a long anchor hole keeps its line.

TIGER 8 pneumatic breaker for site and infrastructure work
Button bits and drill rods for anchor and foundation drilling

Pneumatic breakers and plug hammers for breaking out, trimming and clearing where a machine-mounted breaker cannot be positioned. We do not make hydraulic breakers.

Bits, rods and shanks — 22 × 108 mm shank on the top hammer drills. And the air-line equipment: receivers, hose, fittings and the line lubricator, which is a warranty condition rather than an accessory.

Air flush, water flush, and what your specification says

Some specifications for anchor and dowel work require percussion drilling with air flush and explicitly exclude water, usually to protect the borehole or the surrounding ground. Our drills are air-flush percussion by design, so that clause is met by construction rather than by fitting an option.

Two things worth checking against your own documents before you shortlist anything:

  • Whether the contract is for supply or for works. A notice for the supply or acquisition of equipment is one we can bid. A notice for works is for a contractor, and we are not one — though we are happy to be the named equipment behind a contractor’s bid.
  • Whether a zone classification applies. Our pneumatic drills and motors carry CE and ATEX marking, stated model by model on each product page. We do not extend a certification from one model to another — send the clause and we will answer against it in writing.

What we supply, and what we do not

What we supply

  • Anchor and foundation drilling units, fixed and on a wheeled base
  • Mobile pneumatic drills for tunnel, shaft and confined work
  • A rig for permanent mounting on your own hydraulic excavator
  • A hydraulic column drill where air is not available
  • Hand-held, air-leg and vertical pneumatic drills, 32 to 45 mm
  • Down-the-hole hammers from 75 mm, with the bits, rods and shanks
  • Pneumatic breakers and plug hammers
  • Pneumatic motors and gearboxes for site drives
  • The air-line equipment the drilling runs on
  • Installation, operator training and on-site technical supervision

What we do not supply

  • Nothing that goes into the hole — no anchors, bars, dowels, nails, couplers or grout
  • No protection systems — no mesh, netting, cable nets, catch fences, attenuators or barriers
  • No scaling services or equipment, and no rope-access work
  • No piling, micropile, diaphragm wall or jet grouting rigs — the range stops at 102 mm and about 30 m
  • No boom jumbos and no bolting rigs
  • No shotcrete machines. We supply pneumatic motors to some of the companies that build them, not the machines
  • No earthmoving, loading or haulage, and no hydraulic breakers for excavators
  • No explosives, detonators or blasting services, including trim blasting
  • No compressors or generators — we size what you need, buying it is yours
  • We are not a contractor. We do not execute the drilling, the anchoring or the installation

If your project needs what is in the right-hand column, we will say so rather than quote you the nearest thing we make.

Where these machines have worked

Two projects are written up in full elsewhere on this site rather than retold here, and neither publishes metres drilled or a programme duration, because we did not measure them.

  • A metro line in Bulgaria — shaft and tunnel wall stabilisation alongside running tunnel boring machines, where the deciding factor was positioning a machine in a confined section without holding up the other trades. Read the case study
  • Slope stabilisation on a heritage site — anchor holes for rockfall protection on steep, narrow cliff sections where a larger machine could not be set up at all. Read the case study

The thread running through both is the same one running through this page: on a construction site the limit is almost never the rock. It is whether the machine can stand where the hole has to be.

Tunnel wall stabilisation drilling on a metro construction site

The machine working on a face. It is the most useful answer we have to “will it actually stand up on a slope”.

Questions we get asked

Can you drill on a slope without building a platform first?

That is what the anchor drilling units are designed for, and the video above shows one doing it. Whether it works on your slope depends on the gradient, the ground and how the machine gets there — send photographs of the face and the angle, and we will say yes or no before you commit to anything.

What diameter and depth can you reach?

32 to 45 mm to about 10 m on a top hammer; 76 to 102 mm to 25 to 30 m with a down-the-hole hammer. Beyond those we are not the right supplier and we will tell you so.

My specification says air flush only. Does your drill comply?

Yes — our percussion drills flush with air as built, so a clause excluding water flush is satisfied by construction. Send us the clause and we will confirm against it in writing rather than in a sales email.

Will the excavator rig fit my machine?

The HPDC 1600 is designed for permanent mounting and comes with its mounting hardware and its own diesel unit. It weighs 2,950 kg, so tell us the exact excavator model and we will check compatibility. We do not publish a tonnage class, so we will not guess one at you.

Do you supply the anchors and the mesh as well?

No. We supply the machine that drills the hole, plus installation, training and supervision. Anchors, bars, grout, mesh, netting, fences and barriers all come from system manufacturers, and the installation from a specialist contractor.

Pneumatic or hydraulic on an urban site?

It depends on what is already there. With a compressor on site or easy to bring, pneumatic is lighter to manoeuvre on a face and cheaper to maintain. With a hydraulic power pack, HYDRODRILL gives 450 to 680 N·m of rotation at 100 to 150 bar. We build both, so we have no side to take.

Can you work on a heritage or environmentally sensitive site?

The slope project above was one. In that kind of setting the machine is chosen on footprint, weight and whether it can be carried to the hole, which usually rules out the more powerful options. Describe the constraints and we will say what passes.

Where are the machines made, and what about parts?

Ankara, since 1991, with CNC machining and quality control in house. Parts and technical answers come from the people who built the machine rather than through a distributor.

Tell us where the hole has to go

The diameter, length and angle from the drawing, the rock, how a machine reaches the position, and what you already have on site — compressor, power pack or excavator. We come back with the machine, the air it needs and what to allow for around it. If the job sits outside what we build, we will tell you that instead.

Case Studies

Tunnel and Shaft Wall Stabilization in Metro Construction Site with the Tiger MOBIL DRILL

Infrastructure construction company responsible for the metro line construction in Bulgaria.

Safer and More Durable Solutions on Steep Slopes

The historic Sumela Monastery in Trabzon is a major cultural heritage site, widely known for its unique architecture and high visitor numbers.

Related Products

Mobile Pneumatic Column Drill
Hydraulic DTH Column Drill
Pneumatic Breaker Hammer
Air-Leg Vertical Rock Drill
Pneumatic Hand-Held Rock Drill
Pneumatic Hand-Held Rock Drill
Mobile Pneumatic Anchor & Foundation Drilling Unit
Pneumatic Anchor & Foundation Drilling Unit
Pneumatic DTH Column Drill
Diesel Hydraulic Crawler Drill Rig
Electric Hydraulic Crawler Drill Rig
Hydro-Pneumatic Excavator Drilling Column

Our Latest News & Articles

Stay up to date with insights, product launches, case studies, and trade-show highlights that help quarry and mine operators work safer, faster, and more profitably.

Unlock superior performance for your Machinery Need